VARUN Manusl-EU-DE
Catalogues
Warm Tips................................................2
VARUN Message
Dear friends, thank you for choosing VARUN among many e-bike brands；
VARUN E-Bike is committed to providing people with a safer, more comfortable and environmentally friendly way of traveling, paying great attention to functionality, design, quality and customer experience. We strive to sell our best quality products at the most competitive prices while providing you with the best service. You will not be disappointed when you choose VARUN.
When you receive your VARUN e-bike, you are welcome to send your order number + bike serial number (frame head tube location) to our support center at varunebikes.service@gmail.com and we will activate the one year warranty for you.
We also expect you to tell us your experience and suggestions after riding without reservation, we will continue to improve our e-bikes to bring more customers a pleasant riding experience.
Warm Tips: Please Read The Manual Before The First Ride
- Before riding, please read this manual carefully and check whether the parts are intact to ensure your riding safety, if you find any problem, please contact us in time：varunebikes.service@gmail.com
- Be sure to wear a helmet when riding an e-bike.
- Please keep both keys properly.
- Make sure your e-bike has a full battery before you ride it.
- Always respect pedestrians.
- Do not ride in a wet environment, the e-bike may slip from under your feet and cause injury. Humid conditions may damage the electronic components and void the warranty.
- Please always observe and pay attention to local laws and regulations regarding electric bicycles.
- Please do not disassemble and decompose the parts by yourself, if you need to replace, please contact us to purchase standard parts.
- We should avoid prolonged exposure to sunlight or rain, and avoid storing our e-bikes in places with high temperatures or corrosive gases, so as not to damage the plated parts and painted surfaces.
- If you want to get the best range, follow the instructions below:
- Please use the pedal assist mode.
- Don't brake too often while staying safe.
- Don't overload.
- Before riding, check your tire pressure and provide adequate air pressure, typically between 35PSI-65PSI (280KPA-450KPA).
- E-bikes are a risky mode of transportation, so be sure to follow the rules of the road. In the event of an emergency such as riding too fast, brake the rear wheel first and then the front wheel. If you brake the front wheel suddenly, there is a danger of falling over, so please ride carefully.
- Before riding this e-bike, please check the body condition carefully, and you will be responsible for any consequences caused by improper operation or use of this e-bike.
-
Each bike has its own frame number, located in the head tube position of the frame.When you receive this e-bike, please record and save the frame number, frame number. We have no record.
- Please comply with local laws and regulations, such as your local laws do not allow the use of the speed control handle (or known as the handle, throttle), please do not assemble the speed control handle on the VARUN brand products and use it, or else all the consequences at your own risk, the VARUN brand does not bear all the responsibility.
- Before your first ride, check that all parts/screws of your e-bike are tightened or locked (wheel clamps, saddle clamps, etc.).
All Models Of VARUN E-Bike:
(1)City E-Bike Series
|
(2)Mountain E-Bike Series
|
(3)Fat Tire E-Bike Series
|
Packing List
Carefully inspect the contents of the package and contact VARUN customer service support if anything is missing or damaged:
varunebikes.service@gmail.com
|
Schematic Structure And Parameters Of E-Bike
(1)Urban E-Bike Series (C26-2 as an example)
|
(2)Mountain E-Bike Series (M27-1 as an example)
|
(3)Fat Tire E-Bike Series (C20-1 PRO as an example)
|
(4)26”Fat Tire E-Bike Serie(S26-1 as an example)
|
Basic Parameters Of Each Model：
|
|
|
|
Warm Tip:
- Weight less than 120kg comprehensive riding experience feel better.
- Speed and range vary depending on road conditions, weather, rider weight, etc.
Regarding E-Bike Install:
When you receive the product, please check the list of accessories carefully, please pay attention to safety when installing, and follow the following steps to assemble the vehicle.
Note: The installation steps will be slightly different depending on the product model, the specific in kind shall prevail, please find the corresponding installation steps according to the product model you purchased. In order to protect your safety, please wear protective gloves before installation.
Without permission, do not disassemble or modify the e-bike by yourself. Otherwise, it may cause permanent damage to the e-bike and may cause personal injury.
Scan the code to watch the installation video:Installation Of Handlebars
Suitable For C20-1/C20-1 PRO/S20-1/S20-1 PLUSModel.
- Installation Of Handlebars
- Insert the upper part of the handle riser into the lower part, locking the retaining structure in the middle of the handle riser.
- Stand the riser vertically and lock the folders at the bottom of the riser.
- Make sure the handlebar structure is secured and the handlebars are not wobbly.
Note: When adjusting the height of the handle riser, do not exceed the limit line!
|
2.Suitable For C26-2/C700-2 Model.
Remove the protective plug and insert the handlebar riser against the frame head tube to a depth that must exceed the minimum insertion depth stamped on the handlebar riser vertical tube, then tighten the screw.
Note: Please do not exceed the limit line!
2.Suitable For M26-2/M26-3/C700-1Model .
Install the handlebar into the stem, align the fork, and tighten the screws.
Note: Please do not exceed the limit line!
3.Suitable For M27-1/M24-1/S26-1/M26-1/M26-1 PRO/M26-2 PRO Model .
Turn the handlebar cross tube 180 degrees so it faces forward and tighten the 2 bolts with a No.2 (M4 wrench) tool to secure the handlebar in place.
(2) Adjust The Handlebar Angle:
1.Suitable For C20-1/C20-1 Pro Model.Adjust the handlebars to the proper position and then fasten the handlebar riser clamp ring quick release.
2.Suitable For C26-2/M26-3/M26-2/M24-1 Model.
Use a No.2 (M4 wrench) tool to unscrew the 4 bolts from the stem cover and rotate the handlebars so they are perpendicular to the bike frame; tighten the stem cover against the handlebars and install the 4 bolts back into the stem; tighten the screws again using a No.2 (M4 wrench) tool.
Suitable For All Model E-Bike
- Use a No.8 (M17 wrench) tool to loosen the fork retaining bar and remove it (this accessory is to prevent the fork from deforming during delivery).
- Place the front wheel into the forks, make sure the fork hangers are secured to the axle and make sure the disc is placed in the middle of the brake, tighten the flange nuts on both sides using a No.7 (M15 wrench) tool.
(4) Installation Of Fenders And Lights
1.Suitable For C20-1/C26-2/C20-1 PRO/S20-1/S20-1 PLUS/C700-1/C700-2 Model
- Loosen the screws in the corresponding positions of the front wheels as shown below. Place the fender in this position.
- Attach the headlights and refasten the loose screws. Adjust the position of the lights and tighten the screws.
- Loosen the screws that hold the baffle in place, secure the baffle, and then tighten them again.
Suitable For All Model E-Bike.
Ensure that the threads of each pedal are fully inserted into the crank arm and fully tighten the pedals with a No.7 (M15 wrench) tool.
Note: Turn the pedal labeled "L" counterclockwise into the left crank and the pedal labeled "R" clockwise into the right crank.
(6) Mounting Saddle
Connect the seat and seatpost first, then insert the seatpost into the bar receiver, adjust its position and adjust the height to suit your riding habits, tighten the seat with the clamp.
Note: Do not exceed the maximum saddle height and do not raise the saddle above the safety line!
(7) Installation Of Tail Light/Rear Reflector
1.Installation Of Taillight
For C20-1/C26-2/C20-1 Pro Model E-Bike
- Remove the taillight, install the taillight on the rack and tighten the screws with a tool.
- Connect the plug of the taillight cable and bind the cable to the shelf with a tie wrap.
2.Installation Of Rear Reflector
Suitable For M26-3/M26-2/M27-1/S26-1/M24-1 Model E-Bike.
(8) Installing The Battery
1.For C20-1/C26-2/C20-1 Pro Model E-Bike.
- Insert the battery into the center of the frame and lock it with the battery key.
- Make sure the battery switch is on to enhance your riding experience.
- To remove the battery, insert the battery key and turn it to the unlock position before removing the battery.
2.Suitable For M26-3 Model E-Bike.
First install the battery pouch on the handlebars, then pull the power cord connector out from under the pouch, find the power cord connector, and butt plug the battery's power cord connector to complete the battery installation.
3.Suitable For M26-2/M27-1/M24-1 Model E-Bike.
Open the battery compartment, place the battery at the correct angle, gently insert the battery into the holder, press it down and it will lock automatically. Insert the key into the keyhole and rotate the key to align it with the "OFF" icon, the battery is now locked and cannot be removed.
（9）Adjust The Angle Of The Brake Levers, Gauges, Shifter, Throttle, And Bell On The Handlebars, Then Tighten With a Tool.
After doing the above steps, then the installation part is successfully completed.
Instructions For Use
（1）Meter Introduction
1.Suitable For M24-1 Model E-Bike.
|
Buttons Other Functions: Press and hold "-" for two seconds: booster mode is enabled; Press and hold "+" for two seconds: turn on the headlights and taillights; Simultaneously press and hold "+""-" for two seconds: reset the meter. |
2.Suitable For C20-1/C26-2/M26-2/M26-3/C700-1/C700-2Model E-Bike.
There are three buttons on the instrument, including on/off, plus/headlight, and minus/boost; in the instructions that follow, the on/off button is replaced by the word "ON/OFF", the "+" button is replaced by the word "UP", and the "-" button is replaced by the word "DOWN".
|
Setup Instructions:
|
3.Suitable For C20-1 PRO/M26-1/M27-1/S26-1/M26-1 PRO/M26-2 PROModel E-Bikes.
There are five keys on the operation unit corresponding to the J-56C instrument, including on /off key, "+"key, "-" key, and light keyand function keys"i".
Setup Instructions:
Single Mileage Clear 0: TC represents the zero clearance of a single mileage. Y / N can be selected by long pressing the“+”“-” button, and Y indicates the single mileage. N means no single mileage. Short, under the TC-Y Press “i”Press the button to confirm the function of "single mileage zero".
Assisted Push: When the meter is on, long press [DOWN], after 3 seconds, the electric vehicle enters into the electrically-assisted push state. The electric vehicle drives at a constant speed of 6 kilometers per hour. The screen displays Walk.
Unlocking the speed limit: When the meter is on, long press “-” and “i” at the same time for three seconds to unspeed it.
|
Setup Instructions:
|
4.For M27-1 App Models
The KD716-V instrument matches the K5 buttons and has 5 buttons: ON/OFF, i-button, plus-button, headlight-button, and minus/boost-button; in subsequent descriptions, the ON/OFF button is replaced by the word "ON/OFF"; the i-button is replaced by the word "i"; the plus-button is replaced by the word "+"; and the minus/boost-button is replaced by the word "-".
|
Setup Instructions:
|
（2）Battery Instructions
1.For C20-1/C26-2/C20-1 Pro Model E-Bike.
Familiarize yourself with key ports and key locations before riding. The following figure shows the key ports aligned with the press key port aligned with key location 1, consistent with the ON icon. In key position 1, the battery is in the "ON" position, the battery is locked to the frame, and the key cannot be removed. The key cannot be removed.
|
2.Suitable For M24-1/M26-2/M26-2 PRO/M27-1Model E-Bike.
Before using this product, first you need to turn on the red switch on the top of the battery, press "-" to turn on the battery switch. In key position 1, the battery is in the "locked" state, the battery is locked to the frame and the key is removed so that the bike can be ridden. In key position 2, the battery can be moved and removed. Press the "o" at the top of the red battery switch when the product is not in use.
Brake Adjustment
Before aligning the mechanical disc brake, make sure the brake cable is properly plugged into the brake lever. If the disc rotor is bent or damaged, replace the rotor first.
If the brakes are not sensitive, loosen the fixing bolt of the brake line, shorten the braking distance of the brake line, and then tighten the bolt. Or, when the brakes are too sensitive, lengthen the brake line distance.
If the rotor always rubs against the brake pads or has too much clearance, loosen the two alignment adjustment screws, but do not remove them. Turn the wheel slowly and check the space between the rotor and the brake pads; adjust the position of the pads and rotor so that the rotor and pads avoid rubbing. When adjustment is complete, tighten the screws.
You can also order brakes from specialized dealers. The dimensions are shown on the left (in mm):
Charging: Guidelines For Safe Handling
- Please follow the instructions for use, otherwise you will be responsible for the consequences.
- Please use the original special charger, strictly prohibit the use of other chargers.
- Pay attention to the type of batteries that can be charged by the charger and the applicable voltage, it is strictly prohibited to mix them. Charging time not more than 12 hours.Charging current does not exceed 3A.
- Plug the charger probe into the charger port on the e-bike battery as shown.
- Insert the tip of the cord into the battery charger.
- Insert the AC power plug into an AC outlet. The red indicator light illuminates and stays red until fully charged. When the battery is fully charged, the indicator light turns green.
Error Codes
If there is an electrical problem, "Error" and an error code will be displayed. The detailed meaning of the error is:
|
Product Troubleshooting And Methods
|
Product Precautions
- Battery Notes:
(1) When charging, keep it in a safe place out of the reach of children.
(2) The battery of the e-bike must be stored in an environment with a temperature range of -20 to 45° C. The battery must be stored in an environment with a temperature range of -20 to 45° C. Do not leave the e-bike in a place where the temperature exceeds 45° C. When the ambient temperature falls below -20° C, the battery will enter a self-locking state and cannot be charged or used.
(3) Keep the battery dry, do not place the battery in acidic or alkaline liquids, and keep it away from rain, sources of ignition and high temperature environments. If necessary, keep the metal contacts clean, clean them with a soft and dry cloth.
(4)It is strictly prohibited to reverse the positive and negative terminals of the battery, connect the positive and negative terminals of the battery, and damage, disassemble or short-circuit the battery.
(5)Do not disassemble the battery without permission, or perform any unreasonable operation or unreasonable use of the battery.
(6)Use the original battery, please do not use other brands or products of the battery.
(7)Use the original charger, please do not use other brands of chargers to charge, and other types of batteries are not suitable to use this charger.
(8)Do not cover the charger when charging.
(9)It should not be used when it is not fully charged.
(10)Before charging the e-bike, make sure the charging port is dry and free of faults and foreign objects. Use only the correct socket (100V-240V/50HZ-60HZ) for charging. When charging the e-bike, keep it away from children and pets, and make sure there are no flammable objects nearby.
(11)Do not, under any circumstances, use the e-bike while charging or connecting the charger.
(12)Before using the e-bike, be sure to lock the battery with the supplied battery key and remove the battery key. Please keep the key in a safe place. If it is lost, the user will be fully responsible for it.
(13)If you accidentally immerse the battery or charger completely in water, immediately disconnect the product from power, disconnect the motor from the battery and stop charging, then contact us for technical support in time and do not restart until we have conducted a guided test.
- Battery Handling Precautions:
(1) Batteries must be recycled or disposed of in an environmentally friendly manner.
(2) Do not dispose of the battery in a fire, the battery may explode or leak.
(3) Do not dispose of batteries in your regular household trash.
Product Care Instructions
- Bicycle Maintenance:
(1) Check if the front and rear wheel screws are locked.
(2) Whether the tread pattern of the outer tire is worn and cracked, whether the air pressure of the front and rear tires is appropriate, and whether the driving system is smooth.
(3) Whether the joints of each part are normal, and whether the brake line zipper is used in lubricated condition.
(4) Should always check whether the brake performance is good, pay attention to rain, snow and downhill riding to increase the distance of braking.
(5) lubrication is an important part of the maintenance of the electric car, should be the front axle, the center shaft, flywheel, fork shock absorber rotating pivot point, etc. every six months for a scrub, add grease or oil as needed.
(6) Adjustment of the brake system: loosen the screw on the brake wire fixing seat, and then tighten or loosen the brake wire, so that the average distance between the two sides of the rim and the disk is 0.3㎜-0.5㎜, and finally lock the screw.
- Bicycle Battery Maintenance:
- E-bike every day in the normal driving a certain distance, the same day to the battery should be timely charging, otherwise it will reduce the service life.
- Charge the battery when it is between 30% and 50%.
- Ensure that the battery is not fully discharged (deeply discharged).
- If the vehicle is not used for a long time (to store the battery for more than two months), please pay attention to do regular charging to maintain your battery, otherwise it will reduce the service life or lead to damage to the battery can not be used. Please perform the following operations:
- Fully charge the battery and remove it.
- Make sure there is no visible damage to the battery.
- Fully charge the battery before long-term storage.
- Store batteries in a dry, low humidity area.
- Maintain temperature between 5° C and 20° C.
- Protects batteries from extreme temperature fluctuations.
- Do not expose the battery to direct sunlight or heat.
- Make sure stored batteries are charged every three months.
- The capacity of the battery will slowly decline in the course of use is a normal situation, the final life termination can not be restored.
- In addition to the statutory warranty, VARUN grants electronic components such as “motor”; "Control Unit"; “Display” and “Battery” one year warranty after customer registration.
- Wear parts such as “brakes”; “caliper”;“brake pads”; “Lamps” etc. are excluded from the guarantee. Defects caused by an accident or improper handling are fundamentally excluded.
Any of the following will void the warranty:
- Failure to follow all instructions or recommendations listed in the user manual.
- Single vehicle collision, accident or vehicle damage caused by careless parking.
- Illegal behavior.
- Never registered your e-bike or could not provide an order number.
- DIY repair electronic products.
- Misuse of bicycles on off-road terrain, dirt, snow, water, sand, gravel and water.
- If the bicycle is used as a rental unit.
- Damage caused by earthquake, lightning, fire, flood and other natural disasters.
- Prolonged exposure to rain, hail, snow or direct sunlight can cause rust and/or paint discoloring.
- Overload exceeds recommended load.
- Damage caused by nails, needles, broken glass, debris, sharp stones or other foreign objects.
- Jumping from ramps, stairs or elevated ramps if the bike is used for, but not limited to, stunts.
- If the vehicle is used for competition or racing.
- If modifications have been made to the engine, electrical system, suspension and battery for any purpose.
- Use of other components not approved by the manufacturer.
- Damage caused by improper care and handling.
- Due to the nature of the product, some components must be unique to the manufacturer, such as, but not limited to, batteries, motors, gauges, controllers, Led headlamps, brakes or brake pads. Other components such as tires, inner tubes, saddles, racks, baskets may be used from listed or compatible products pre-approved by the retailer or manufacturer.
- If you have any questions about the warranty or to make any claims, please contact VARUN Service at:
Email: varunebikes.service@gmail.com
Return Policy
(1) Return Shipping Costs:
- If the return is due to quality, damage, and incorrect items, VARUN will cover the return shipping costs;
- If the return has nothing to do with quality, damage, or incorrect items, but is simply at the buyer's personal and last minute discretion, the customer will have to bear the return shipping costs;
- If you need us to provide you with a pre-paid waybill, please let us know and you print the return label and stick it on the box and take the package to the nearest logistics store such as DHL (if the return is caused by the customer himself, then the return shipping fee will be deducted from the refund).
(2) The returned device must be like new, including all original packaging, accessories and documentation. Any missing components may be deducted from the refund. Any shipping damage during the return process may be deducted from the refund.
(3) Refunds will be issued within an average of 1-2 weeks after we have received, inspected and processed the returned merchandise. Your refund will be returned to your original method of payment.
(4) If the customer wishes to cancel the order after the shipping label has been created, the customer will be responsible for shipping charges.
PLEASE NOTE: Warranty claims can only be made at your dealer or directly at VARUN Customer Service. Please do not return your e-bike without prior consultation. Otherwise the package may be refused and any resulting costs will be your responsibility.
FAQ
Q: Where and by whom can I have my bike in and assembled?
A: Basically, any good bike store should fit it for you when you pay to have it fitted (since they didn't buy the bike there). However, there are official social bike shops that offer this service as well. You can find them at the Federal Employment Agency:
Q: How does customer service/warranty work after the sale?
A: When you have a problem with your bike, please leave us a message on the platform where you bought your bike or contact us directly: varunebikes.service@gmail.com
We will get back to you within one business day. It is best to describe your problem in detail and send pictures or make a video showing your problem. We will report your problem/video to our technical team and give you a solution.
Q: Can I ride in the rain?
A: Yes, there is no problem riding in moderate or light rain. Please make sure that the bike is completely dry before your next ride, and make sure that the bike is completely dry before your next ride, otherwise the bike will randomly disconnect. However, do not park your bike in the rain or wade through water. Soaking the vehicle and electrical components in water is prohibited.
Q: What is the most important thing I can do to maintain my battery?
A: Remember to charge your bike in a timely manner and do not leave it with an empty battery. Remember, if you don't use the battery for a long time, charge the battery every 2 months or the battery will starve to death because it has no power. No power. This will result in short trips or the display not coming on.
Q: Do you have a spare key for my e-bike?
A: Hi, we don't have a spare key, please keep your key safe in case you lose it.
Q: What is the range of my VARUN battery?
A: This depends on the situation, on factors such as the battery itself (capacity, condition, charging cycles); the landscape (even in the mountains); the weather (tailwind or headwind, cold/warm); the power support (low/high), etc. It is generally impossible to answer. Under laboratory conditions, each VARUN bike was driven over 100 kilometers during the test. It is recommended that you use the Pedal Assist mode, which improves range.
Q: From time to time, my display gives me errors, flashes, and occasionally goes out instead of coming on!
A: There may be poor battery contacts here. First clean the contacts on the battery, spray with WD 40 / Caramba or similar product and check that the battery is correctly placed in the supplied stand. If the battery is wobbling in the support, secure it. If the display goes out while driving, the contact between the battery and the control unit may be broken. It also makes sense to check the contacts on the control unit directly here.
Q: Can the handlebars of the M27-1, S26-1 and M24-1 be raised?
A: The height of the handlebars on these models is not adjustable and can only be adjusted with "handlebar risers" from specialized dealers. Since our bikes come in standard sizes, there are a variety of options here. Other handlebar models can be raised.
Q: I want to buy another bike!
A: Ask our sales people for a "loyalty discount" on another new bike or a cheap refurbished bike (1 year warranty). We are here to help, just send us an e-mail.
